Rubber Bullets

-
RUBBER BULLETS:

 Rubber Bullets An offbeat military application of rubber is the use of rubber bullets as non-lethal weapons.

 Peace-keeping missions involving crowd control, as well as military prison duty, often require the use of non-deadly force.
 In military parlance, the function of these and other non-lethal weaponry is ‘to incapacitate personnel and material, while minimising fatalities, permanent injuries to personnel, and undesired damage to property and the environment’ Civilian police and security services employ rubber-coated metal bullets, plastic (e.g., PVC or polymethyl methacrylate) bullets, and beanbags filled with lead pellets for riot control and personnel protection.


However, rubber bullets generally cause less injury than other nonlethal rounds. The misuse of nonlethal weaponry is a paramount legal issue
Rifles, grenades and a variant on the clay more mine are used by the military to spray nonlethal rubber pellets.

 The polymers used in various rubber bullets include ethylenepropylene-diene (EPDM), polybutadiene, natural and synthetic polyisoprene, styrene butadiene copolymer, butyl rubber, and various blends.
The elastomer is usually highly filled with carbon black, clay, calcium carbonate, or metallic fillers such as copper or iron.



Comments

Post a Comment

Popular posts from this blog

Calendering

-
Image
Introduction: Calendering is the process of making thin sheet of rubber and also lamination of such sheet on to other substrate like fabric,cord warp sheet by passing through set if rollers under controlled Conditions. A calendar comprises of a number of rows or bowls held in frame. Rolls rotate in opposite directions either with even speed or with a friction ratio. Types Of Rubber material used Elastomers that can be used include: ·          Neoprene ·          SBR ·          Natural ·          Hypalon ·          Urethane ·          EPDM          Viton           Fluroelastomer         Butyl          Nitrile         Silicone Fabric Materials Rayon Cotton Polyester Blends Monfilament Blends Kevlar Fiberglass Nylon Square Woeven Polyester Fiberglass Nomex ·        Advantage of Calendering: 1.Accurate rubber sheet gauge across the full length. 2.Frictioning operation for rubberized fabric 3.Skim coating
Read more

Types of Bridge Bearing

-
Image
Types of bridge bearing  1. Elastomeric Bearing a.Plain elastomer pads b.Laminated Elastomeric bearings 2.Sliding bearing Mechanism a. PTFE  sliding material b.Alternative sliding material 3.High load multi Rotational building: a.Pot bearing b.Disc bearing c.Spherical bearings 4. Fabricated steel mechanical bearing a.Rocker bearing b.Rocker cum rolling bearing Elastomeric Bearing: It consists of elastomer manufactured from synthetic or natural rubber and can take both translation and rotation movements through elastomer deformation. The ability of elastomer to carry large vertical loads is because of reinforcement provision that prevents lateral bulging of elastomer. There are number of elastomeric bearing pads classified based on types of reinforcements used. For example, steel reinforced, plain, fiberglass reinforced and cotton duck reinforced elastomeric bearing pads Strength and response of each type is different, steel reinforced ela
Read more

Shrinkage rate Calculation

-
I n Moulding process the rubber is Cured at high temperature and Pressure, the resulting Moulded parts are smaller in size than the actual. The Difference in the thermal expansion of the mold material result in shrink rate Shrink Rate= ( Cavity dimension- Part Length)/ Cavity dimension) (Typical units in/in) This shrinkage value is applied to the desired finished part size to “scale up” the cavity. The resulting cavity dimension is calculated as: Cavity Dimension= finished part length/ (1- Shrink rate) For example: Shrinkage rate testing was performed on a 70 Shore A Nitrile (Buna-N), Ethylene-Propylene (EP), Fluorosilicone (FVMQ), and 75 Shore A Fluorocarbon (FKM).  The Fluorosilicone and Fluorocarbon materials undergo a secondary vulcanization process called post-curing. During the post-curing process, the molded parts were baked in a ventilated oven at a specific time and temperature recommended by the material manufacturer, or at a temperature great
Read more